32212-80G04 Manual Transmission Counter Gear for Nissan

The 32212-80G04 counter gear is a Nissan manual transmission component. Match it to the original gear arrangement when rebuilding the transmission.

Compare the complete gear-tooth sequence, shaft dimensions and bearing locations. Include the transmission identification and a clear view of both ends of the original part with your enquiry.

Send the transmission code, component number, tooth and spline counts and quantity. Include the principal dimensions and photographs of the original part.

Contact TOSEN for a quotation or browse Transmission Parts.

The 32212-80G04 counter gear is an internal component of a Nissan manual transmission, not a complete gearbox assembly. The counter gear, also called the layshaft gear, is a toothed wheel that runs on the countershaft inside the gearbox case. It meshes with the input shaft and with the individual mainshaft gears to transfer drive across the transmission, so it carries load from the engine every time the vehicle is in a driven gear. Because the gear teeth are in constant mesh when the gearbox is turning, wear on the counter gear shows up as noise, whine or a damaged tooth surface, and the part is replaced during a gearbox rebuild or repair when the original is worn or damaged. It is selected by its reference number and by matching the tooth and shaft details to the gearbox being serviced.

• Reference number: 32212-80G04
• Component: Counter gear (layshaft gear) — an internal part, not a gearbox assembly
• Vehicle application: Nissan
• Role in the system: transfers drive across the manual gearbox by meshing with the input shaft and the mainshaft gears

The 32212-80G04 counter gear is specified for Nissan manual transmissions. Because it is an internal part rather than a complete gearbox, the deciding factor is the transmission identification and the physical details of the gear itself, not the vehicle model alone. A workshop should confirm which manual gearbox is fitted and then compare the counter gear against the removed part on the points that matter: the complete gear-tooth sequence and tooth count, the shaft diameter and the bearing locations. Two Nissan transmissions from the same era can use different counter gears, so matching the reference number 32212-80G04 together with the measured dimensions and a clear view of both ends of the original part gives the most dependable identification.

• Reference to match: 32212-80G04
• Component to match: counter gear for a Nissan manual transmission
• Primary checks: complete gear-tooth sequence and tooth count
• Secondary checks: shaft diameter and bearing locations against the removed gear
• Workshop planning: include the transmission identification and photographs of both ends of the original part

The 32212-80G04 counter gear is supplied as a new component. TOSEN sources manual transmission parts through a factory-direct supply channel and checks each gear against the reference number 32212-80G04 and the tooth and shaft details described on this page before dispatch, so that the part presented for installation corresponds to the requirement stated in the order. Because this is an internal gear rather than a completed gearbox, the enquiry should name the transmission being serviced and give the tooth count and the principal shaft dimensions of the original part. Distributors and transmission workshops rebuilding Nissan gearboxes can request a sample so the gear details are confirmed against the original before a larger order is placed.

Is the 32212-80G04 a complete gearbox or a single gear?

The 32212-80G04 is a single counter gear for a Nissan manual transmission, not a complete gearbox. The counter gear is an internal layshaft component that meshes with the input shaft and the mainshaft gears to transfer drive across the transmission. It is replaced during a rebuild or repair when the original gear is worn or damaged, and it is selected by its reference number together with the tooth and shaft details of the gearbox being serviced.

Which Nissan transmissions use the 32212-80G04 counter gear?

The 32212-80G04 counter gear is specified for Nissan manual transmissions. Because it is an internal part, the transmission identification and the physical details of the gear are the deciding factors rather than the vehicle model alone. Confirm which manual gearbox is fitted to your vehicle and compare the reference number, the gear-tooth sequence and the shaft dimensions against the removed part, because different Nissan transmissions can use different counter gears.

How do I verify the 32212-80G04 counter gear before ordering?

Compare the gear against the removed part on the points that identify it: the complete gear-tooth sequence and tooth count, the shaft diameter and the bearing locations. Confirm the reference number 32212-80G04 and note the transmission identification from the gearbox being serviced. Supplying a clear view of both ends of the original gear with the enquiry helps TOSEN confirm the match before the order is placed.

What should I include with a 32212-80G04 counter gear enquiry?

Send the transmission code, the component number 32212-80G04, the tooth and spline counts and the quantity required, together with the principal dimensions and photographs of the original part. Note the vehicle application and the gearbox identification. This lets TOSEN confirm that the counter gear matches the Nissan manual transmission being rebuilt before dispatch.