To match a differential pinion flange to the retained prop-shaft, record the central pilot’s diameter and male or female form, the bolt-hole layout and fastening details, and the axial position of the mating face. Include the shaft-side joint or yoke interface. A correct gear ratio and the same bolt count leave those features unresolved.
Use an end view and a side view with labelled dimensions and units. Measure accessible features on a stationary assembly prepared under the workshop’s handling procedure; leave pinion-flange removal and axle setup to the applicable service procedure. The comparison below is an identification record, not an installation tolerance.
Separate the pilot register from the bolt holes
The pilot, also called the register, is the central projection or recess that mates with the opposite flange. Label both sides: a male projection and a female recess can have similar nominal diameters, but they describe complementary features. Keep that dimension separate from the outside diameter of the flange.
- Pilot form and diameter. Mark male or female on the end-view sketch. Measure the actual cylindrical register surface, rather than a chamfer or a nearby dust shield. Record damage or wear that makes the reading uncertain.
- Pilot height or recess depth. On the side view, show the projection or recess from the flat mating face. This identifies another feature for comparison; the required engagement and clearance come from the applicable drawing.
- Hole count and fastening. Record the number of holes and whether they are plain, threaded or fitted with studs. Record plain-hole diameter separately from a confirmed thread specification; a caliper reading across a threaded hole does not establish its thread pitch.
- Flange outline. Note the overall diameter or outline and any locating features. These help identify the part, while the pilot and hole pattern describe different parts of the mating interface.
Use a suitable caliper or depth-measuring tool for the accessible feature and record the actual reading. Preserve the part and axle identification beside it. A worn old surface is a reference for identification, not a new-part acceptance limit.
Measure the hole pattern from its centres
Bolt circle diameter, or PCD, is the diameter of a circle through the hole centres. Adjacent hole spacing is a chord of that circle. Record the actual layout as well as the count so that a rectangular four-hole pattern cannot be mistaken for a square one.
- Draw the end face. Mark every hole centre and the central register. Add an orientation mark so the supplier can follow your horizontal, vertical and diagonal measurements.
- Identify the centre-to-centre distances. For equal-size plain holes, the outside-to-outside span across two holes minus one hole diameter gives their centre spacing. Keep the measuring line through the two centres. Mark uncertain or damaged edges rather than rounding them into a nominal size.
- Name the measured distance correctly. When two hole centres lie directly opposite each other through the flange centre, their centre spacing is the PCD. Adjacent spacing is not the PCD. For a centred rectangular four-hole pattern, record both perpendicular centre spacings; its diagonal is the bolt-circle diameter.
As a geometry example, a square pattern with 60 mm between adjacent hole centres has a diagonal of about 84.9 mm, not 60 mm. This illustrates the measurement distinction; it is not a specification for a vehicle or replacement part. For an irregular or uncertain pattern, send the individual centre locations or a dimensioned drawing instead of forcing a single PCD value.
Manufacturer flange-yoke catalogues distinguish hole spacing, hole or thread size and bolt circle as separate fields. Keep millimetres and inches explicit on your sketch; a unitless “four-bolt, 85” description leaves both the feature and its units unclear.
Put axial measurements on a labelled side view
Name the starting plane for every axial dimension. To compare complete differential assemblies, use the same identified housing mounting plane and show its distance to the prop-shaft mating face. A dimension taken from a casting edge cannot be compared directly with one taken from a machined mounting face.
For a flange yoke, record the flange-face-to-U-joint-centre distance separately. This describes the yoke’s geometry; it is different from the housing-to-flange-face dimension. Draw the joint centre on the side view so that a supplier cannot interpret “flange length” as either one.
Record the actual joint interface too. A U-joint arrangement needs its applicable series or confirmed bearing and retention dimensions; a CV joint or another coupling needs its corresponding mating reference and geometry. Matching the flange face does not establish joint compatibility. Likewise, these measurements alone do not approve the installed prop-shaft length, operating angles or sliding travel.
Resolve a mismatch before changing the pinion flange
If the ratio is correct but the flange comparison differs, first request an assembly with the correct documented interface. Treat a proposal to transfer the old flange or add an adapter as a separate compatibility and service question, rather than completing the original order by assumption.
Flange removal can involve axle setup conditions. For example, GM bulletin PI1354, covering 2014 Chevrolet Silverado 1500 and GMC Sierra 1500, gives specific crush-sleeve, bearing-preload and flange-runout conditions around removal or replacement. Those conditions are model-specific; they do not supply a universal removal count or tightening method for another axle.
Ask the rebuilder for the applicable axle procedure and the checks required for the proposed change. The external pilot and bolt pattern do not describe the pinion-side splines, seal-running surface or bearing arrangement. This measurement record therefore provides no instruction to loosen the pinion nut, alter the flange or set bearing preload.
Send a like-for-like flange comparison
Put old-part observations and the offered assembly’s corresponding details in the same record. Label which side of the connection each reading describes: the two mating pilots should be complementary, while the flange pattern must correspond. Use the drawing’s specified fit rather than requiring every male and female reading to be numerically identical.
| Feature | Existing assembly / retained shaft | Offered assembly | Unit and reference |
|---|---|---|---|
| Axle and part identity | Record references and confirmed ratio | Request corresponding references | Tag, part number and drawing revision |
| Pilot/register | Male or female; measured diameter | Request form and specified diameter | mm or in; mark the actual cylindrical surface |
| Pilot axial feature | Projection height or recess depth | Request matching feature | From the flat mating face |
| Hole pattern | Count, sketch and centre spacings / PCD | Request the same layout details | mm or in; identify each centre pair |
| Holes and fastening | Plain-hole size or confirmed thread / studs | Request corresponding fastening details | Diameter; thread size and pitch where applicable |
| Assembly axial position | Housing datum to mating face | Request from the same datum | Name and mark the reference plane |
| Joint or flange-yoke interface | Joint reference; face-to-joint-centre where relevant | Request corresponding geometry | Part reference and labelled side-view dimensions |
A matching ratio with a different pilot form, hole layout or axial datum is an unresolved interface, not an accepted substitute. If only one reading is uncertain, identify that feature for further measurement or a manufacturer drawing. Keep the remaining observations, rather than restarting with a vague vehicle-model request.
Questions about uncertain measurements
Can a photograph replace the dimensioned sketch?
A photograph helps identify the face and locating features, but perspective and scale make it unreliable as the only dimensional record. Add actual readings, units and marked reference surfaces. Keep the original part identification with both images.
What if rust or wear affects the pilot reading?
Mark the reading as uncertain and identify the affected surface. Compare the nominal dimension with the applicable part drawing or an unworn reference confirmed for that part. Do not convert a damaged old measurement into a new-part fit tolerance.
Is outside flange diameter enough to identify the replacement?
No. It does not describe the central register, hole centres, fastening or axial position. Use the full comparison record and the exact axle or component reference before selecting a replacement.
Compare the offered interface before ordering
When comparing differential assemblies, send the axle identity and confirmed ratio together with the labelled flange measurements. Ask for the offered assembly’s corresponding interface details so that a correct ratio does not conceal a prop-shaft mismatch.
Use TOSEN’s catalogue to locate the relevant differential family, then take the end view, side view and completed comparison to the parts discussion. Resolve any interface difference before placing the order.


