
The 9472600945 Mercedes synchronizer ring is a single replacement component – one friction and timing ring for Mercedes-Benz truck transmissions, not a kit and not a complete synchronizer. It also travels under more than one number: parts catalogues list the same component under a second Mercedes-Benz reference, 9472603045, and under the ZF cross-reference 0073301185. Those extra numbers are the first reason an order can go wrong, and the first thing a buyer should check.
The second reason is the application spread. Trade listings map this one reference across a wide Mercedes-Benz truck family and a long list of ZF gearbox versions, so the truck model name alone never settles which ring a specific gearbox needs. This buyer checklist walks through what the reference covers, how the numbers relate, which level the match must run through, and the six checks that make the first order the correct one.
What the 9472600945 Reference Actually Is
Order 9472600945 and one synchronizer ring arrives: the friction and timing element that matches gear speeds before the engagement teeth mesh. It is a single replacement part for truck gearbox rebuilds – not a synchronizer cone, not a hub-and-sleeve set, and not a complete synchronizer. The number itself appears in several written forms. Catalogues space it as A 947 260 09 45 or 947 260 09 45, and listings compress it to 9472600945; the digits are identical, so a differently spaced number is not a different part.
| Reference | What it is | What to do when you see it |
|---|---|---|
| 9472600945 | Mercedes-Benz reference for the ring; the primary ordering number | Quote it in full, exactly as printed on the removed part or documentation |
| A 947 260 09 45 | The same Mercedes-Benz reference in spaced catalogue form | Treat it as identical – no re-check needed beyond the digits |
| 9472603045 | A second Mercedes-Benz reference that parts catalogues list for the same component | Treat as a check trigger: confirm both numbers point to one ring before ordering |
| 0073301185 | ZF cross-reference for the same component, used where the gearbox is documented by its ZF number | Either number identifies the ring for ordering – record which one your documentation uses |
Two references on one component are common where a gearbox family appears under different documentation, and either number identifies the same ring for ordering. The dual numbering is not permission to guess. A listing that shows only 9472603045 next to your 9472600945 is describing the same catalogue component, but a listing that truncates a number or mixes references from a neighbouring position is not – and the neighbouring positions in these gearboxes carry their own rings with their own geometry. When any doubt survives the table above, the six checks in this article close it before money moves.
Where the Ring Fits: Truck Family and Gearbox Versions
The core application is the Mercedes-Benz Actros MP2 and MP3 generation, and the TOSEN AUTO catalogue lists the ring as produced to the standard dimensions of the original fitment. Around that core, trade and catalogue listings map the same reference across a wide family – Atego, Axor, Econic and Zetros appear beside further Mercedes-Benz truck lines – and across the ZF G-series gearboxes these trucks use. That spread is real, not listing inflation: parts catalogues attach the reference to roughly nineteen gearbox versions, from G131-9 and G211-12 KL through G240-16, G260-16 and G280-16, each designation carrying a ratio suffix that separates it from its siblings.
| Item | Description |
|---|---|
| Reference | 9472600945 – Mercedes-Benz reference; ZF cross-reference 0073301185 |
| Component | Synchronizer ring, supplied as a single replacement part |
| Core application | Mercedes-Benz Actros MP2 MP3 truck transmissions |
| Broader family | Atego, Axor, Econic, Zetros and further Mercedes-Benz truck lines in trade listings |
| Gearbox versions | ZF G-series designations with ratio suffixes – around nineteen versions across catalogues |
| Matching rule | Match the transmission model, the synchronizer position and the ring geometry – not the truck model name |
A spread this wide is exactly why the match runs through the gearbox version. Two Actros cabs from different build years can carry different G-series gearboxes, and the ring that fits a G211-16 does not follow from the truck badge on the door. During the teardown, record the gearbox designation from the tag or documentation – the full code with its ratio suffix – and keep it with the synchronizer position and the removed ring. That record, not the truck name, is what the order is built on.
The Buyer Checklist: Six Checks Before You Order
- The complete reference number – 9472600945 in full, or its documented ZF cross-reference, exactly as printed; a truncated or half-remembered number can point at a neighbouring ring
- The gearbox identification – the full G-series designation with its ratio suffix, recorded from the gearbox tag or documentation during teardown
- The synchronizer position – the position the removed ring served; each position in these gearboxes carries its own references, and this reference's position is not published in a single public catalogue, so the teardown record is the authority
- The ring geometry – profile, teeth and dimensions of the removed ring, compared with the replacement before the order completes
- Markings and photographs – the numbers on the removed part, plus photographs of the original ring and its mating components, so the order carries its own evidence
- Quantity and destination – pieces per position and gearbox version, and the delivery destination, sent with the enquiry so the quotation rests on the same record
Each check exists because it closes a specific failure. A complete number rules out sibling-reference confusion. A recorded gearbox version rules out the wrong-variant shipment across a nineteen-version spread. Position and geometry together rule out the neighbouring-position ring that carries a similar number but a different tooth form. Photographs let the supplier see what the paperwork cannot describe, and the quantity-and-destination line keeps a multi-gearbox rebuild from being quoted one ring at a time. Careful inspection of every part going back into a gearbox is also the standing discipline in transmission service manuals – parts damaged in handling or transit are reject candidates, and the same thinking applies to what you accept from a supplier.
On the supplier side, TOSEN checks each 9472600945 enquiry against exactly these details – the reference, the gearbox model, the synchronizer position and the recorded geometry – before quoting, so the quotation and the shipped ring answer to the same record. The enquiry form on the 9472600945 synchronizer ring product page takes the field set directly, which is the practical way to send check six with the order.
Ring, Kit or Assembly: What to Order
The reference ships one synchronizer ring – and only the ring. Whether the rebuild needs more is a separate question the teardown answers, not the order form. The ring is the wearing friction element, but it works against the cone on the gear and inside the hub-and-sleeve grouping, and those mating surfaces wear too. Grinding or baulking shifts at the affected position are the classic signs that the ring's friction surface is spent; the synchronizer ring wear symptoms guide maps those complaints to their causes in detail. A new ring timed against a worn cone or rounded engagement teeth will grind and jump out early, repeating the failure the rebuild was meant to close.
| What you order | What it includes | Order it when |
|---|---|---|
| The 9472600945 ring | One synchronizer ring, single replacement part | The ring is scored or worn and the mating parts measure clean |
| Ring plus mating parts, ordered separately | The ring plus the cone or hub-and-sleeve parts the teardown shows worn | Wear extends past the ring itself; each part ordered on its own reference |
| Complete synchronizer assembly | The full matched grouping for the position | The whole grouping shows wear and the position is being fully renewed |
Two site guides carry the detail this table compresses. The ring versus cone versus sleeve identification guide explains which of the three parts a rebuild actually needs, and the ZF synchronizer ring wear inspection guide shows how to measure wear instead of judging it by eye. Whatever scope the measurements support, confirm the composition at the enquiry – the order record should state which parts are included, so the crate that arrives matches the rebuild that waits on it.
Wholesale Orders: Enquiry Fields, Samples and Arrival Checks
A wholesale enquiry is the six-check record with volume specifics attached: the reference, gearbox version, position and geometry stay exactly as recorded, and the order grows around them rather than replacing them. The transmission parts category shows the neighbouring components a wider rebuild orders alongside the ring. What a volume order adds is the field set below.
- Quantity per position and per gearbox version, so a multi-version rebuild is quoted as one record
- The delivery destination, so freight is quoted with the parts
- Photographs of the original ring and its mating components
- One approved sample, qualified against the original before the production batch
The sample step is the heart of it. Compare a sample ring against the original on the same geometry points, confirm the reference and scope on the sample itself, and require the production batch to match the approved sample – producing from a customer's sample or drawing is standard practice in this trade, so the request is normal, not special. No public source pins this reference to a single material grade, and rings in this gearbox family circulate in more than one friction material, so the sample's material is the standard the batch must match, not an assumed grade. A batch that drifts from its sample in tooth form or ring profile turns a stock order into a shelf of unusable parts, and for the measured checks themselves the ZF synchronizer ring wear inspection guide shows what a bench comparison looks like on a synchronizer ring.
When the delivery arrives, check it against the same record before the gearboxes go back together: match the delivered rings against the photographs and numbers from the teardown, compare pieces within the batch so every ring matches the sample, and inspect for transit damage – a ring that has been bent or dropped in handling is a reject candidate, not a fitting risk to absorb. At assembly, follow the lubrication practice the transmission service manuals set for synchronizer parts, and note that some ring materials in this gearbox family carry an explicit pre-lubrication requirement in supplier catalogues – treat the specified lubricant as part of the order, not an afterthought. The request-a-quote form on the 9472600945 synchronizer ring page takes the six-check fields directly, and the transmission parts category covers the neighbouring components a wider rebuild needs.
A complete wholesale enquiry, at a glance
One reference, quoted in full: 9472600945.
One gearbox version, not a truck model name.
One position and one geometry record, from the teardown.
One approved sample, before the production batch.
One quantity and destination, with photographs of the original.
Frequently Asked Questions
Is the 9472600945 a single ring or a kit?
It is a single synchronizer ring – the friction and timing element for Mercedes-Benz truck transmissions. Ordering the reference ships one component, not a cone, hub or sleeve set. If the rebuild needs more than the ring, each additional part is ordered on its own reference, and the composition is confirmed at the enquiry.
Why do listings show 9472603045 or 0073301185 for the same ring?
Parts catalogues list the same component under a second Mercedes-Benz reference (9472603045) and a ZF cross-reference (0073301185). Two references on one component are common where a gearbox family appears under different documentation, and either number identifies the ring for ordering. Confirm the pairing in the catalogue rather than assuming it from a listing title.
Can I order this ring by truck model name alone?
No. The reference spans a wide Mercedes-Benz truck family and around nineteen ZF gearbox versions, so the truck name leaves the version open. Record the full G-series gearbox designation with its ratio suffix during the teardown and order against that, keeping the truck name as context only.
Which gear position does this ring serve?
No single public catalogue publishes the position for this reference, so do not order on an assumed one. Record the synchronizer position from the gearbox during the teardown – each position carries its own references – and send it with the enquiry. The supplier-side check resolves the position against the gearbox version before quoting.
Should I replace just the ring or the whole synchronizer?
Let the teardown measurements decide. A scored ring with clean mating parts needs only the ring; wear that extends to the cone or the hub-and-sleeve grouping calls for those parts on their own references; a fully worn grouping at the position justifies the complete assembly. A new ring against worn mating surfaces repeats the original failure.
What should a wholesale enquiry for this ring include?
The six-check record – reference, gearbox version, position, geometry, markings, quantity – plus the volume increments: destination, photographs, and one sample qualified against the original before the production batch. Require the batch to match the approved sample, and check the delivery against the same record on arrival.
Order the Record, Not Just the Number
A reference this widely applied is safe to order only when the order carries more than the number. The checklist is short: the complete reference, the gearbox version with its ratio suffix, the synchronizer position, the removed ring's geometry, the photographs, and the quantity with its destination. Run it once and the sibling numbers, the nineteen-version spread and the neighbouring-position rings all stop being risks – the record settles them before the payment does.
Send the completed field set through the enquiry form on the 9472600945 synchronizer ring product page, and TOSEN checks each enquiry against the reference, gearbox version, position and geometry before quoting. Prefer another route? Take the checklist with you – it works the same way with any supplier.


